Microchip logo
  • All
  • Products
  • Documents
  • Applications Notes
product primary image

USB7052

Status: In Production

Features:

  • USB Type-C PD support on upstream port (100W)
  • USB Type-C PD support on two downstream ports (15W/15W)
  • Integrated Hub Feature Controller (HFC) enabling I/O Bridging and FlexConnect
  • I/O Bridging: Host communication to external peripherals USB to I2C/SPI/GPIO bridge endpoint support
  • FlexConnect: Host port Swapping and Switching to downstream Devices Reversible upstream and downstream Port 1 roles on command
  • Battery Charging - USB-IF rev1.2 support on downstream ports (DCP, CDP, SDP) including legacy Apple® iOS, Blackberry®, China Charging and many others
View More
Overview
Documents
Development Environment
Similar Devices
RoHS Information
Add To Cart

Device Overview

Summary

The Microchip USB7052 PD Smart Hub™ IC is a low-power, OEM configurable, USB 3.1 Gen 1 hub controller with 4 downstream ports and advanced features for embedded USB applications. The USB7052 is fully compliant with the Universal Serial Bus Revision 3.1 Specification and USB 2.0 Link Power Management Addendum. The USB7052 supports 5 Gbps Super-Speed (SS), 480 Mbps Hi-Speed (HS), 12 Mbps Full-Speed (FS), and 1.5 Mbps Low-Speed (LS) USB downstream devices on all enabled downstream ports.

Along with the UPD350 Power Delivery transceiver or equivalent device supporting PD, the USB7052 supports USB Power Delivery 3.0 with up to 100W of power on the upstream port.  The two USB Type-C downstream port only supports up to 15W of power.  All the USB70512 USB Type-C ports include internal USB 3.1 Gen 1 multiplexers; no external multiplexer is required for Type-C support.  The USB7052 is USB-IF certified as a Power Delivery enabled USB3.1 Gen1 hub (TID1212).

A SmartHub IC is defined as a USB hub that integrates system levels functions typically associated with a separate MCU or processor.  The USB7052 SmartHub IC enables communication to other peripherals in addition to USB. This I/O Bridging capability allows the host to seamlessly interface to peripherals via I2C, SPI or GPIOs over USB.  The USB7052 also enable a downstream device to take control of the host system by swapping roles and becoming the host port. The USB7052 can also switch between two different hosts if required. This role changing technology is called FlexConnect and can be initiated through hardware or software commands.

The USB7052 also supports the legacy USB speeds (HS/FS/LS) through a dedicated USB 2.0 hub controller that is the culmination of six generations of Microchip hub feature controller design and experience with proven reliability, interoperability, and device compatibility. The SuperSpeed hub controller operates in parallel with the USB 2.0 controller, decoupling the 5 Gbps SS data transfers from bottlenecks due to the slower USB 2.0 traffic.

The USB7052 supports downstream battery charging with integrated battery charger detection circuitry supporting the USB-IF Battery Charging (BC1.2) detection method and most Apple devices. The USB7052 provides the battery charging handshake and supports the following USB-IF BC1.2 charging profiles: DCP: Dedicated Charging Port (Power brick with no data); CDP: Charging Downstream Port (1.5A with data); SDP: Standard Downstream Port (0.5A with data); Custom profiles loaded via SPI EEPROM or OTP.

MPLAB Connect Configurator, Microchip’s proprietary software utility, can be used to program On-chip One Time Programmable (OTP) ROM for the USB7052 which stores required register settings to ensure the desired start up configuration at power on. All LED, GPIOs and port control signal pins are under firmware control, allowing for maximum operational flexibility. However, for even more simplicity, the USB7052 can be configured through a series of external low-cost resistor bootstraps. A handful of bootstap pins are available on the USB7052 to enable standard configurations for GPIOs and downstream ports. No OTP programming required. 

*The USBCheck online design review service is subject to Microchip's Program Terms and Conditions and requires a myMicrochip account.

Parametrics
Name
Value
Upstream Port
USB3.1 Gen1
USB Speed
USB3.1 Gen1
Downstream Ports
4
MGMT I/F
I2C
ROM I/F
SPI
Op Voltage (V)
3.3
MultiTRAK Tech
Yes
PortMap
Yes
PortSwap
Yes
TrueSpeed
Yes
PHYBoost
Yes
Temp. Range Min.
-40
Temp. Range Max.
85

Documents

Jump to:

Supporting Collateral

Development Environment

  • Demo & Evaluation Boards
  • Software Libraries
Demo & Evaluation Boards
EVB-USB7050 - USB Type-C PD Evaluation Board
EVB-USB7050 - USB Type-C PD Evaluation Board ( EVB-USB7050 )

The EVB-USB7050 is a demonstration and evaluation platform that provides the necessary requirements and interface options for evaluating the USB7050, which is a 4-port High-Speed (HS), Native USB Type-C™ SmartHub™ IC on a 4-layer RoHS-compliant Printed Circuit Board (PCB) with support for three ports of Power Delivery (PD). This allows the user to gain an understanding of the product...

Learn More
Software Libraries
MPLAB(r) Connect Configurator - Programming and Configuration Utility

Follow this link for the latest revision of the MPLAB(r) Connect Configurator -> Click

...

Learn More
USB70xx Linux Application Code Examples

This document provides release information about USB70xx Linux Application Code example to support many of the unique functionality of the USB70xx SmartHubs

Learn More

Similar Devices

Product
Price 5K
$1.31
$1.03
$1.71
$2.29
$2.52
$2.52
$4.04
$1.55
$1.09
 
$1.41
$1.97
$1.45
$3.17
$3.02
$1.97
$2.56
$2.63
$1.80
$2.70
$1.80
$2.70
$2.89
$2.85
 
$3.54
$3.71
 
$4.17
$4.84
$4.17
$3.10
$3.44
$5.16
$5.16
$5.04
$5.04
$5.40
$5.40
$5.76
$5.16
$5.40
$5.76
$4.78
$5.35
$5.20
$5.07
$5.63

RoHS Information

Part Number
Device Weight (g)
Shipping Weight (grams)
Lead Count
Package Type
Package Width
Solder Composition
JEDEC Indicator
RoHS
China EFUP
USB7052/KDX
0.295100
1.250000
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB7052-I/KDX
0.295100
1.250000
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB7052T-I/KDX
0.295100
0.686400
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB7052T/KDX
0.295100
0.686400
100
VQFN
12X12X0.9mm
Matte Tin
e3
To see a complete listing of RoHS data for this device, please Click here
Shipping Weight = Device Weight + Packing Material weight. Please contact sales office if device weight is not available.

Buy from the Microchip Store

Grid
View
Table
View
Filter:
Apply
Clear
Only show products with samples
Product
Leads
Package Type
Temp Range
Packing Media
5K Pricing
Buy