Microchip logo
  • All
  • Products
  • Documents
  • Applications Notes
product primary image

USB5807C

Status: In Production

Features:

  • Seven downstream USB3.1 Gen1/2.0 ports
  • Reversible upstream and downstream Port 1 roles on command
  • PortSplitting - USB downstream port can be split for custom applications using embedded USB3 devices in parallel with USB2.0 devices.
  • Battery Charging - USB-IF rev1.2 support on downstream ports (DCP, CDP, SDP) including legacy Apple® iOS, Blackberry®, China Charging and many others
  • Industrial grade temperature support (−40°C to +85°C)
View More
Overview
Documents
Development Environment
Similar Devices
RoHS Information
Add To Cart

Device Overview

Summary

Microchip’s USB5807C SmartHub is a 7 port, SuperSpeed (SS), low power, configurable USB3.1 Gen1 hub and fully compliant with USB-IF's USB 3.1 Gen1 specification (TID1595). This supports the latest ECNs for USB-IF logo compliance for the new USB Type-C™ industry initiative.  The USB5807C also supports Hi-Speed (HS), Full Speed (FS) and Low Speed (LS) USB signaling, offering complete coverage of all defined USB operating speeds. The new SuperSpeed hubs operate in parallel with the USB 2.0 controller, so 5 Gbps SuperSpeed data transfers are not affected by slower USB 2.0 traffic.

The USB5807C is also a SmartHub which is defined as a USB hub that integrates system levels functions typically associated with a separate MCU or processor.  The USB5807C SmartHub enables a downstream device to take control of the host system by swapping roles and becoming the host port. The SmartHub can also switch between two different hosts if required. This role changing technology is called FlexConnect and can be initiated through hardware or software commands.

The hub also can expand beyond seven ports through PortSplitting which allows for embedded applications to only use the interface needed for internal, non-removable USB connections.

MPLAB® Connect Configurator, Microchip’s proprietary software utility, can be used to program On-chip One Time Programmable (OTP) ROM which stores required register settings to ensure the desired start up configuration at power on. All LED, GPIOs and port control signal pins are under firmware control, allowing for maximum operational flexibility. However, for even more simplicity, the USB5807C can be configured through a series of external low-cost resistor bootstraps. A handful of bootstap pins are available on the USB5807C to enable standard configurations for GPIOs and downstream ports. No OTP programming required..

*The USBCheck online design review service is subject to Microchip's Program Terms and Conditions and requires a myMicrochip account.

Additional Features
  • Seven downstream USB3.1 Gen1/2.0 ports
  • Reversible upstream and downstream Port 1 roles on command
  • PortSplitting - USB downstream port can be split for custom applications using embedded USB3 devices in parallel with USB2.0 devices.
  • Battery Charging - USB-IF rev1.2 support on downstream ports (DCP, CDP, SDP) including legacy Apple® iOS, Blackberry®, China Charging and many others
  • Port Config Straps - Predefined configuration of port settings – Battery Charging ports, Non-Removable ports, Disabled ports
  • USB Link Power Management (LPM) support
  • IETF RFC 4122 compliant 128-bit UUID
  • Compatible with MSFT Windows 10, 8, 7, XP, Apple OS X 10.4+, and Linux hub drivers
  • Available in 100-pin (12mm x 12mm) VQFN RoHS compliant package
  • Industrial grade temperature support (−40°C to +85°C)
  • Applications
    • Expansion Hubs
    • Docking Stations
    • LCD Monitors
    • HDTVs
Parametrics
Name
Value
Upstream Port
USB3.1 Gen1
USB Speed
USB3.1 Gen1
Downstream Ports
7
MGMT I/F
I2C
ROM I/F
SPI
Op Voltage (V)
3.3
MultiTRAK Tech
Yes
PortMap
Yes
PortSwap
Yes
TrueSpeed
Yes
PHYBoost
Yes
Temp. Range Min.
-40
Temp. Range Max.
85

Documents

Jump to:

Data Sheets

Brochures

Development Environment

  • Demo & Evaluation Boards
  • Software Libraries
Demo & Evaluation Boards
EVB-USB5807 Evaluation Board
EVB-USB5807 Evaluation Board ( EVB-USB5807 )

The EVB-USB5807 is a demonstration and evaluation platform that provides the necessary requirements and interface options for evaluating the USB5807,a 7-Port SS/HS USB Smart Hub on a 4-layer RoHS-compliant Printed Circuit Board (PCB). This will allow the user to gain an understanding of the product and accelerate the integration of the USB5807 into the user’s design. The EVB-USB5807 is...

Learn More
Add To Cart
Software Libraries
MPLAB(r) Connect Configurator - Programming and Configuration Utility

Follow this link for the latest revision of the MPLAB(r) Connect Configurator -> Click

...

Learn More

Similar Devices

Product
Price 5K
$1.31
$1.03
$1.71
$2.29
$2.52
$2.52
$4.04
$1.55
$1.09
 
$1.41
$1.97
$1.45
$3.17
$3.02
$1.97
$2.56
$2.63
$1.80
$2.70
$1.80
$2.70
$2.89
$2.85
 
$3.54
$3.71
 
$4.17
$4.84
$4.17
$3.10
$3.44
$5.16
$5.16
$5.04
$5.04
$5.40
$5.40
$5.76
$5.16
$5.40
$5.76
$4.78
$5.35
$5.20
$5.07
$5.63
$5.65
 

RoHS Information

Part Number
Device Weight (g)
Shipping Weight (grams)
Lead Count
Package Type
Package Width
Solder Composition
JEDEC Indicator
RoHS
China EFUP
USB5807C/KD
0.295100
1.250000
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB5807C-I/KD
0.295100
1.250000
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB5807CT/KD
0.295100
0.686400
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB5807CT-I/KD
0.295100
0.686400
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB5807C/KDH01
0.295100
1.250000
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB5807C-I/KDH01
0.295100
1.250000
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB5807CT/KDH01
0.295100
0.686400
100
VQFN
12X12X0.9mm
Matte Tin
e3
USB5807CT-I/KDH01
0.295100
0.686400
100
VQFN
12X12X0.9mm
Matte Tin
e3
To see a complete listing of RoHS data for this device, please Click here
Shipping Weight = Device Weight + Packing Material weight. Please contact sales office if device weight is not available.

Buy from Microchip

Grid
View
Table
View
Filter:
Apply
Clear
Only show products with samples
Product
Leads
Package Type
Temp Range
Packing Media
5K Pricing
Buy